Weber Saint-Gobain - Official website of the company

weberepox easy

weberepox easy
weberepox easy

Product benefits

    • Two components easy to mix
    • Easy to apply
    • Easy and fast to clean
    • Good workability after 1 hour at 40°C
    • High compressive strength at 14 days
    • Excellent chemical resistance
    • Non-sag
    • Slip resistant when used as tile adhesive
    • Good heat aging resistance
    • Anti-Stain

Two components epoxy tile grout and adhesive

weberepox easy is a 100% reactive, 2-component epoxy tile grout and tle adhesive with very easy water cleanable properties exceeding the requirement of the standard ANSI 118.3, excellent chemical resistance, high strength, and easy application. it is designed for numerous application needs. In addition to its waterproofing and excellent workability properties, it is especially blended to produce non-sag and stain resistant properties when used as tile grout, non-slip property when used as tile adhesive and high compressive strength at 48 hours. Due to its special additives, the product maintans a good workability after 1 hour at 40 deg C.

weberepox easy is particularly recommeded fo tile grouting in medium and heavy duty, hygienic and corrosive enironment 

Product Features


  • Two components easy to mix
  • Easy to apply
  • Easy and fast to clean
  • Good workability after 1 hour at 40dg C
  • High compressive strength at 14 days
  • Excellent chemical resistance
  • non-sag
  • Slip resistant when used as tile adhesive
  • Good heat aging resistance
  • Anti-stain

Scope of use

  • Tiling and grouting of ceramics, mosaics, stones, etc...
  • Specially recommended for bathrooms, showers, and kitchens (private and collective)
  • Repair of damaged tile joints.
  • Tiling on special substrates such as metal, etc...
  • Highly resistant to chemical aggressions, cleaning under high pressure and heavy traffic
  • For internal and external walls and floors
  • Food production: fruit canning, meat & fish processing, dairy products, etc...
  • Industries, car showrooms, etc..
  • Swimming pools


Appearance 2-component
Part A Resin + filler
Part B Hardener
Colors 23 colors available
Application Easy mixing and application
Mix density 1.781
Pot life 4 hours
Stain resistance good
Sag resistance non sag
Slip resistance non slip
Compressive strength 85.7 MPa at 7 days (ANSI A118.3)
Tensile strength 22 MPa
Water cleanability Water cleanable at 80 minutes ANSI A118.3
Resistance to chemicals reagents Available upon request BS EN 12808-1:2008
VOC and formaldehyde content USEPA 24 Low VOC


When used as a tile glue, consumption is from 2.5 to 6 kg/m².
C = 0.18 x E x H x [(L + W) / (L x W)]
C : Consumption (kg/m²)
E : Joint Width (mm)
H : Tile Thickness (mm)
L : Tile Length (cm)
W : Tile Width (cm)
For tiles of 10 mm thickness, consumption will be from 0.5 to 2.5 kg/m².



weberepox easy can be stored for 1 year in dry conditions, away from extreme temperatures.




Send or download the documentation

You can either send the documentation to an email address, or download it.

Instructions for use

Surface preparation


Before grouting, joints and the tile surface should be clean with a damp sponge to remove dust, dirt, and other contaminants. Do not leave water standing in joints. Do not clean tiles with acid cleaners.



New concrete must be a minimum of 28 days old. The surface to be covered shall be sound, dry, rigid, clean and free from impurities like grout, dirt, debris, oil, grease, curing agents, loose plaster etc




Product preparation

Remove part B (hardener) from inside the part A (resin + filler) pail and pour it into the part A.

Mix well with a suitable electrical mixer at low speed (around 2 minutes) to ensure the proper chemical reaction until a smooth paste is obtained. Do not mix part A separately.





Product application




weberepox easy should be applied directly into the joints. By using a rubber trowel or scrapper fill the empty joints diagonally to ensure the joints are well filled. Remove excess grout with a grout float. Do not leave excess grout on face of tiles.

Smoothing the joints by using a wet sponge then clean the tiles immediately, before the product dries, by using a clean and wet sponge. The tiles are cleaned easily with water. weber.epox easy can be applied for joints width from 2 to 10mm.

Ready for pedestrian after 24 hours at 25 ºC and for heavy traffic after 48 hours at 25 ºC.


Mix the two components and spread the adhesive over the surface using a serrated trowel. Tiles should be placed within the open time of the adhesive. Due to the slip resistance properties of the material, tiles can be fixed vertically. Press firmly the tiles to ensure a good adhesion and remove surplus material from the face of the tiles immediately.










Clean tools and equipment with solvents such as Xylene, Xylol or Toluene. Do not allow the epoxy to harden on equipment


weberepox easy can be stored for 1 year in dry conditions, away from extreme temperatures

Environmental and Safety


While the company guarantees its products against defective materials, the use and application of these products are made without guarantee since the conditions of their application are beyond its control. It is recommended to verify with the company that the product is suitable for the intended use, and that this Data Sheet version is the latest one. The company may modify it without prior notice. Technical characteristics are listed for guidance only. For more information, please contact the company’s office in your location.


The information included on this Technical Data Sheet is the sole property of SODAMCO Holding. The unauthorized disclosure, use, dissemination or copying (either whole or partial) of this data sheet or any information it contains, is prohibited and subject to legal pursuit.

Available packaging

Lebanon4 kg
Syria4 kg
Jordan4 kg
KSA4 kg
UAE4 kg
Qatar4 kg
Kuwait4 kg
Oman4 kg