Weber Saint-Gobain - Official website of the company

webercol epo

formerly Epotile

webercol epo
webercol epo

Product benefits

  • For heavy duty sites
  • Chemical resistant/ anti -bacterial
  • Adhesion on steel/metal
  • Moisture insensitive
  • Fast curing

Three-component epoxy tile adhesive

webercol epo is a 100% reactive, 3-component epoxy tile adhesive system designed for numerous application needs. It is a moisture insensitive fast curing system specially blended to produce a workable mortar. It provides excellent chemical resistance and outstanding adhesion on steel, concrete and tiles.

Product Features

Scope of use

webercol epo is especially designed for fixing tile on floor where heavy and fast load, and chemical resistance is required. webercol epo can be used for a thickness above 8mm as tile adhesive in medium and heavy duty, hygienic and corrosive environment. It can be used in the following industries:

  • Food Production – including meat, and fish processing, fruit canning, dairy products, etc.
  • Chemical productions and processing
  • Brewing and Distilling
  • Soft drink production and bottling
  • Workshop and garage.

Advantages

  • 100% solids
  • Moisture insensitive for bond to dry or damp surfaces
  • Resistant to chemical attack, including most acids and caustics
  • Hygienic in service, will not support bacterial growth
  • High mechanical and bonding qualities to all round substrate

Characteristic

Appearance 3-component
Part A Resin
Part B Hardener
Part C Mineral charge
Colors Grey (after mixing)
Mix density 1.89 +/- 0.05
Flash point > 150ºC
Pot life Approx 1 hour at 30ºC
Compressive strength 67.5 MPa at 7 days(ASTM C 579)
Adhesion on concrete > 2.5 MPa (BS 1881)
Tensile strength 9.8 MPa (ASTM C307)
Flexural strength 29.1 MPa (ASTM C580)
Consumption 15 kg/m² depending on thickness.

Documentation

Send or download the documentation

You can either send the documentation to an email address, or download it.

Instructions for use

Surface preparation

New concrete must be a minimum of 28 days old and possess an open, porous and textured surface with all curing compounds and sealers removed. Old concrete must be clean and well textured. All oil, dirt, debris, paint and unsound concrete must be removed.

Product preparation

Part B (hardener) is to be added to part A (resin), not the reverse. Mix parts A and B for 1 minutes using a suitable electrical agitator (Heavy Duty) at low speed to ensure the proper chemical reaction. Gradually add the filler (part C) to the premix of parts A and B and continue mixing for a further 2 minutes until all the aggregates are completely wetted by the epoxy

Product application

For Flooring only: The mixed adhesive should spread over the surface using a serrated trowel. Tiles should be placed within the open time of the adhesive. Remove surplus material from the face of the tiles immediately.

Cleaning

Clean tools and equipment with solvents such as Xylene, Xylol or toluene. Do not allow the epoxy to harden on equipment

Environmental and Safety

Safety precautions

Ensure adequate ventilation during application and avoid inhalation of vapors, Wear suitable gloves, clothing and eye protection.
Direct contact with eyes will cause irritation and may cause serous damage if not treated. In case of contact with eyes, wash thoroughly with clear water and seek medical attention.

Disclaimer

While the company guarantees its products against defective materials, the use and application of these products are made without guarantee since the conditions of their application are beyond its control. It is recommended to verify with the company that the product is suitable for the intended use, and that this Data Sheet version is the latest one. The company may modify it without prior notice. Technical characteristics are listed for guidance only. For more information, please contact the company’s office in your location.

Note

The information included on this Technical Data Sheet is the sole property of SODAMCO Holding. The unauthorized disclosure, use, dissemination or copying (either whole or partial) of this data sheet or any information it contains, is prohibited and subject to legal pursuit.
PG.13
Edition:05/13-A

Available packaging

Lebanon17.5 kg
Syria17.5 kg
Jordan17.5 kg
KSA17.5 kg
UAE17.5 kg
Qatar17.5 kg
Kuwait17.5 kg
Oman17.5 kg