Weber Saint-Gobain - Official website of the company

webercol epo plus

formerly Epotile plus

webercol epo plus
webercol epo plus

Product benefits

  • For heavy duty sites
  • Chemical resistant/ anti -bacterial
  • Adhesion on steel/metal
  • Moisture insensitive
  • Fast curing

Thin bed epoxy tile adhesive

webercol epo plus is a 100% reactive solvent free, water-cleanable designed for numerous applications needs. It provides excellent chemical resistance and exceptional adhesion on ceramic tile/vitrified tile/stone cement board, concrete and steel/metal surface. It is chemical resistant, waterproof, moisture insensitive and fast curing system specially blended to produce a non-sag material.

Product Features

Scope of use

webercol epo plus can be used as tile adhesive in medium and heavy duty, hygienic and corrosive environment. It can be used in the following industries:

  • Food Production – including meat, and fish processing, fruit canning, dairy products, etc.
  • Chemical productions and processing
  • Brewing and Distilling
  • Soft drink production and bottling
  • Workshop and garage.


  • 100% solids
  • Water Cleanable
  • Moisture insensitive for bond to dry or damp surfaces
  • Resistant to chemical attack, including most acids and caustics
  • Hygienic in service, will not support bacterial growth
  • High mechanical and bonding qualities to various substrates.


Appearance 3-component
Part A Resin
Part B Hardener
Part C Mineral charge
Colors OFF white (after mixing)
Mix density 1.8 ± 0.05
Flash point > 150ºC
Pot life Approx 1 hour at 30ºC
Water cleanable ANSI A118.3
Compressive strength 50 MPa at 7 days(ASTM C 579)
Adhesion on concrete > 2.5 MPa (BS 1881)
Consumption 5 to 10 kg/m² depending on thickness.


Send or download the documentation

You can either send the documentation to an email address, or download it.

Instructions for use

Surface preparation

New concrete must be a minimum of 28 days old. The surface to be covered shall be sound, dry, rigid, clean and free from impurities like grout, dirt, debris, oil, grease, curing agents, loose plaster etc.

Product preparation

Part B (hardener) is to be added to part A (resin), not the reverse. Mix parts A and B for 2 minutes using a suitable electrical agitator at low speed to ensure the proper chemical reaction. Add gradually the mineral charge (part C) to the premix of parts A and B and continue mixing for a further 2 minutes until all the mineral charges are completely wetted by the epoxy.

Product application

Apply webercol epo plus evenly on the substrate with the notched side of the trowel using a scrapping motion to ensure good contact with the substrate. Additional adhesive may then be applied to have a uniform thickness of 3 to 5 mm maximum. Apply the tiles on the substrate and press them firmly, while making sure that the paste does not slip from the tile sides. For large tiles, webercol epo plus can also be applied on the back of tiles to ensure full adhesion with the entire surface. Tiles should be placed within the open time of the adhesive. Remove surplus material from the face of the tiles immediately.


Clean tools and equipment with water and soap while the material still wet or use solvents such as Xylene, Xylol or toluene. Do not allow the epoxy to harden on equipments.

Environmental and Safety

Safety precautions

Ensure adequate ventilation during application and avoid inhalation of vapors, Wear suitable gloves, clothing and eye protection.
Direct contact with eyes will cause irritation and may cause serous damage if not treated. In case of contact with eyes, wash thoroughly with clear water and seek medical attention.


While the company guarantees its products against defective materials, the use and application of these products are made without guarantee since the conditions of their application are beyond its control. It is recommended to verify with the company that the product is suitable for the intended use, and that this Data Sheet version is the latest one. The company may modify it without prior notice. Technical characteristics are listed for guidance only. For more information, please contact the company’s office in your location.


The information included on this Technical Data Sheet is the sole property of SODAMCO Holding. The unauthorized disclosure, use, dissemination or copying (either whole or partial) of this data sheet or any information it contains, is prohibited and subject to legal pursuit.

Available packaging

Lebanon18 kg
Syria18 kg
Jordan18 kg
KSA18 kg
UAE18 kg
Qatar18 kg
Kuwait18 kg
Oman18 kg