Weber Saint-Gobain - Official website of the company

webercol flex FS

formerly Carroflex FS

webercol flex FS
webercol flex FS

Product benefits

  • Fast setting
  • Waterproof
  • Highly flexible
  • Very high bonding
  • Non-slip (non-sag)

Two components fast-setting cementitious flexible tile adhesive (latex modified)

webercol flex FS is a two components polymer modified fast-setting flexible ready-mix tile adhesive. Its flexibility makes it suitable for tiling directly to timber and concrete substrate subject to thermal/shrinkage movement. It is specially formulated for interior and exterior wall and floor applications. webercol flex FS is water resistant and has an outstanding bonding effect. (Grey color)

Product Features

Scope of use

webercol flex FS is suitable for the rapid set laying of all ceramic, mosaic stone, brick, clay and non-porous tiles. The fast setting nature of this material makes it ideal for situations where the tiled area need to be accessed/grouted in few hours such as: shops, hospitals, and commercial and domestics situations. Over difficult substrates such as gypsum, wood..., primer is required, consult company for advice.

Characteristics

Appearance Powder
Composition Special cements, siliceous sand and additives
Color Dark Grey
Pot Life 15 min at 20°C
Setting Time (min.) Initial set: 90min ; Final set: 210min
Shelf Life 6 months
Mixing Ratio 5.5 lit. per 25 kg
Consumption 3 to 7 kg/m²
Tensile Adhesion at 20 hours 0.95 MPa
Service Temperature -20°C to +70°C

Test for en 12004:2013

Open Time by Tensile
Adhesion acc. EN 1346:2007 (N/mm²)
5 minutes 1.1
10 minutes 0.7
Tensile Adhesion
Stregth acc. EN 1348:2007
(N/mm²)
Con A 2.6
Con B 0.9
Con C 2.5
* Con A - 28 days standards conditions
* Con B - 7 days standard condition + 21 days water immersion
* Con C - 14 days standard condition + 14 days at 70˚C
* Standard Condition - (50 ± 5)% Relative Humidity & 23 (± 2)˚C

Test for ANSI A118.10

7 days standard conditions2,4
28 days standard conditions2,1

Applicable standards

EN 12004:2007,EN 12002, ANSI A118.4

Storage

webercol flex FS can be stored for 6 months in dry conditions, away from extreme temperatures and protected against wind.

 

 

Documentation

Send or download the documentation

You can either send the documentation to an email address, or download it.

Instructions for use

Surface preparation

Substrate must be structurally sound and free from loose tiles and debris, existing setting material or any foreign matters.

Product preparation

Mix the two components of webercol flex FS by pouring the powder in the liquid progressively while stirring the liquid.
An electric mixer with low rotation speed (< 300 rpm) can be used. Mix until a uniform lump free paste is obtained.

Product application

Apply webercol flex FS evenly on the substrate. Use a notched trowel to have the required thickness. Apply the tiles on the substrate and press them firmly, while making sure that the paste does not slip from the tile sides. webercol flex FS can also be applied on the back of tiles to ensure full adhesion on the entire surface.

Cleaning

Clean the tools with water after use. Cured materials can only be removed mechanically.

Precautions

The mixed webercol flex FS should be used within 15 minutes from mixing time at 20°C.
It is recommended to determine the suitability of all materials before proceeding with the installation

Environmental and Safety

Safety precautions

The product contains cements powders which, when mixed with water, release alkalis that could be harmful to the skin. It is preferable that the application be done in a ventilated area, and to wear protective gear for hands, eyes and respiratory system and to avoid breathing of the dust. Splashes on the skin should be washed away by cleaning thoroughly with soap and water. In case of contact with eyes, wash thoroughly with clean water and seek medical attention. If swallowed, do not induce vomiting and seek medical attention. The product is non-flammable.

Disclaimer

While the company guarantees its products against defective materials, the use and application of these products are made without guarantee since the conditions of their application are beyond its control. It is recommended to verify with the company that the product is suitable for the intended use, and that this Data Sheet version is the latest one. The company may modify it without prior notice. Technical characteristics are listed for guidance only. For more information, please contact the company’s office in your location.

Note

The information included on this Technical Data Sheet is the sole property of SODAMCO Holding. The unauthorized disclosure, use, dissemination or copying (either whole or partial) of this data sheet or any information it contains, is prohibited and subject to legal pursuit.
PG.13
Edition:05/13-A

Available packaging

Lebanon12.3+2.7kg , 25+5.5 kg
Syria12.3+2.7kg , 25+5.5 kg
Jordan12.3+2.7kg , 25+5.5 kg
KSA20+4.4kg
UAE12.3+2.7kg , 25+5.5 kg
Qatar12.3+2.7kg , 25+5.5 kg
Kuwait12.3+2.7kg , 25+5.5 kg
Oman12.3+2.7kg , 25+5.5 kg