Weber Saint-Gobain - Official website of the company

weber cerafix - KSA

weber cerafix - KSA
weber cerafix - KSA

Product benefits

  • Internal use
  • Wet and dry conditions
  • Water resistant

Cementitious tile adhesive

weber cerafix is a ready-mix cement-based tile adhesive for internal use.
weber cerafix is water resistant and has a strong bonding effect and can fix a wide range of tiles

Product Features

Scope of use

weber cerafix can fix a wide range of ceramic tiles.

weber cerafix can be used to tile directly onto the following substrates:

  • Concrete
  • Cementitious plaster and renders
    Gypsum substrates are not advisable.
    weber cerafix to be used in dried areas. It has good property in bathrooms and kitchens

Characteristics

Appearance Powder
Composition Cement, siliceous sand and additives
Color White
Density 1.55 kg/lit. ± 0.05
Pot Life 2 hrs at 20°C
Shelf Life 12 months
Mixing Ratio 4 to 4.8 lit. per 20 kg
Consumption 3 to 7 kg/m²

Test for en 12004:2012

Open Time by Tensile
Adhesion acc. EN 1346:2007 (N/mm²)
5 minutes >0.6

 



 

Applicable standards

EN 12004
EN 1346, EN 1348

Storage

weber Cerafix can be stored for 12 months in dry conditions, away from extreme temperatures.

 

 

Documentation

Send or download the documentation

You can either send the documentation to an email address, or download it.

Instructions for use

Surface preparation

Substrate must be clean and free from greasy matters or dust. It should have been sufficiently cured in a way that any shrinkage has already occurred. Moisten slightly the substrate if it is dry at the time of application, never moisten the tiles.

Product preparation

Mix weber cerafix in the proportion of 4 to 4.8 liters of water for 20 kg bag. An electric mixer with low rotation speed (< 300 rpm) can be used.
Mix until a uniform lump free paste is obtained. Let the paste rest for a few minutes before starting the application.

Product application

Apply weber cerafix evenly on the substrate. Use a notched trowel to have a uniform thickness according to the size of the tile.
Apply the tiles on the substrate and press them firmly,while making sure that the paste does not slip from the tile sides. weber cerafix can also be applied on the back of tiles to ensure full adhesion on the entire surface. In case exceptional performance is required, each bag of 20 kg of webercol fix should be mixed with 1 liter weberad 225 MB (styrene butadiene latex bonding agent) + 3 liters clean water.

Cleaning

Clean the tools with water after use. Cured materials can only be removed mechanically.

Precautions

Apply weber.col fix on the substrate by areas of around 1m² each, which can be tiled within a maximum of 15 minutes from application time at 20°C. After that time, an outer skin may form thus preventing the tile from adhering properly to weber.col fix. Adjustments to the tiles should only be made during its open time.
It is recommended to leave a minimum width of 2 mm around the tiles (or as designed). Grouting the tile joints should only be done at least 24 hours after tiling, using weber.joint perfect or weber.joint (Carrojoint).

Environmental and Safety

Safety precautions

The product contains cement powders which, when mixed with water, release alkalis that could be harmful to the skin. It is preferable that the application be done in a ventilated area, and to wear protective gear for hands, eyes and respiratory system and to avoid breathing of the dust. Splashes on the skin should be washed away by cleaning thoroughly with soap and water. In case of contact with eyes, wash thoroughly with clean water and seek medical attention. If swallowed, do not induce vomiting and seek medical attention. The product is non-flammable.

Disclaimer

While the company guarantees its products against defective materials, the use and application of these products are made without guarantee since the conditions of their application are beyond its control. It is recommended to verify with the company that the product is suitable for the intended use, and that this Data Sheet version is the latest one. The company may modify it without prior notice. Technical characteristics are listed for guidance only. For more information, please contact the company’s office in your location.

Note

The information included on this Technical Data Sheet is the sole property of SODAMCO Holding. The unauthorized disclosure, use, dissemination or copying (either whole or partial) of this data sheet or any information it contains, is prohibited and subject to legal pursuit.
PG.13
Edition:05/13-A

Available packaging

Lebanon20 kg
Syria20 kg
Jordan20 kg
KSA20 kg
UAE20 kg , 25 kg
Qatar25 kg
Kuwait25 kg
Oman20 kg , 25 kg